Skip to main content

09. Controlling the bulb at your home using an LDR

LDR, short for Light Dependent Resistor, also known as photoresistor is made of semiconductor material. The resistance of an LDR decreases with increasing light intensity. 
*Safety precaution: If you are a beginner, please do not tamper with mains electricity. As this project is for beginners, I will show you how to use an alternative. The power bank and LED are good alternatives to mains electricity supply and bulb.

Supplies:

  • LED
  • LDR
  • Relay Module - Single channel 5V
  • Resistors - 1kΩ and 10kΩ
  • Arduino Uno R3
  • Solderless Breadboard - Mini
  • Power bank - 10000 mAh
  • Old USB 1.0/2.0 A type cable
  • Jumper Wires
  • Jumper Cable

Setting up your hardware




Connections:

  • LDR - A0

Coding

Final Look



Comments

Post a Comment

Popular posts from this blog

51. Buzz wire game using Arduino

Hello everyone! This is my first Arduino project in 2020 and it is going to be a fun and simple project. You would have heard of the Buzz Wire, a steady hand game, and today you will be learning to make one using Arduino. Hardware components used in this project Arduino Nano USB Type A to mini B cable (for Arduino Nano) Solderless Breadboard - Mini and Full-size LEDs (x2) - Green and Red Resistors (x2) - 220 Ω  Active Buzzer module (KY-012) LCD display module with I2C interface - 16x2 Male-to-Male Jumper wires (x4) - 10cm Female-to-Male Jumper wires (x5) - 20 cm Jumpers (x5) - to reduce the usage of wires Copper wire  Tape (or any form of insulation)  Setup Your hardware setup must look somewhat similar to the ones in the images above. The beginning and end of the copper wire maze must be taped to prevent conductivity between the wire loop and maze. Connections LCD display module with I2C interface GND - Ground VCC - 5V SDA -...
Post a Comment
Read more

71. Buzz Wire Game ( Version 2.0 ) using Arduino

Hey Everyone! I hope that everyone's safe during this pandemic. Today I am going to explain you about the second version of my Buzz wire game. People who are bored of staying indoors can find this game pretty interesting and fun to play.  If you are a beginner, you can start off with my first version of this project :  51. Buzz wire game using Arduino   Hardware components used in this project Arduino Uno Solderless Breadboard (x2) - Full/ Full+ LCD display module with I2C module - 16x2 Potentiometer - B20K Push-buttons (x3) Resistor - 220 Ω Active Buzzer module (KY-012) LED - Red Copper Wire - 19/ 20 gauge thick Male-to-Male Jumper wires - 10cm and 20cm Wire - Long enough to connect the loop of copper wire to ground Other tools required for this project Cutting pliers - To cut the right amount of copper wire Round-nose pliers - To bend the copper wire and make a maze and loop Hardware setup Connections Wire Maze - D2 Wire loop - Ground (GND) B20K Potentiometer S - A0 (+)...
1 comment
Read more

86. RFID Health tag (Arduino and Python)

 Hey everyone, Sorry I have not uploaded in a while. Today, I will be sharing an interesting project with all of you. This RFID Health tag project is useful when it comes to keeping track of vaccinated individuals, their biodata and their health conditions and medications. For this project, you will be needing Arduino and Python. Read on further to see how I did this project. Hardware components used in this project Arduino Uno Solderless Breadboard - Half+ MRFC522 RFID reader RFID key tags (x5) Push-buttons (x2) Male-to-Male Jumper wires (x12) USB Type A/ B cable (for Arduino Uno) Software required Arduino IDE - latest version recommended Python 3.8 Schematic MFRC522 RFID reader SDA/ SS - D10 SCK - D13 MOSI - D11 MISO - D12 IRQ - Not connected GND - Ground RST/ RESET - D9 3.3V - 3.3V Push-buttons Submit button - D4 Retrieve button - D5 Coding Arduino For this project, you will be using the following libraries: MFRC522 by miguelbalboa -  https://github.com/miguelbalboa/rfid SP...
Post a Comment
Read more