Skip to main content

Home

Welcome to Arduino Projects by R!

Arduino projects are becoming more popular nowadays. They turn out to be really interesting when you get an insight about what is actually happening. It is okay if you are new to this, you can take a look at the 'Introduction' page to get a basic understanding of Arduino.

*Note: The projects in this page are subject to copyrights (All rights reserved). These projects must not be republished without the owner's permission.

Basic requirements

  • Arduino programmable circuit board  
I will be using Arduino Uno R3 as it is more compatible than Arduino Uno.

  • Solderless Breadboard

I will be using a mini solderless breadboard throughout my projects because in my opinion, they are okay for basic projects.

  • Jumper wires
It is similar to normal wires except for its connector or pin at each end which makes it easier to connect with the Arduino board, breadboard, actuators and sensors when prototyping a circuit.


Comments

Post a Comment

Popular posts from this blog

77. Controlling Micro servo Robotic Arm with MPU-6050 sensor module

 Hey everyone! I am back with an interesting project. Today, you will be learning about controlling a Simple 2 axis Robotic Arm, made from Micro servo motors, with an MPU-6050 sensor module. Please feel free to visit my previous blog post to learn about the MPU-6050 sensor module. Hardware components used in this project Arduino Mega 2560 - You could use any other Arduino microcontroller, but make sure you use an external power supply. USB Type A/B cable (for Arduino Mega 2560) MPU-6050 sensor module SG-90 Tower Pro Micro Servo motor (x2) Male-to-Male Jumper wires (x6) Male-to-Female Jumper wires (x5) Setup Schematic MPU-6050 sensor module VCC - 3.3V GND - Ground SDA - D20 (Arduino Mega 2560), A4 (Arduino Uno and Nano) SCL - D21 (Arduino Mega 2560), A5 (Arduino Uno and Nano) INT - D2 Micro servo motor (Roll) S (Yellow/ Orange) - D9 + (Red) - 5V - (Black/ Brown) - GND  Micro servo motor (Pitch) S (Yellow/ Orange) - D10 + (Red) - 5V - (Black/ Brown) - GND Coding As I alread...
Post a Comment
Read more

57. Using Blynk with Arduino Uno and ESP8266 WiFi module

Hello Everyone! Today I am going to explain you how to connect your Arduino Uno with Blynk using the ESP8266 WiFi module. I have already demonstrated you about connecting your Arduino Uno with Blynk app using the Ethernet Shield W5100 and this will be the second version of that project .  Hardware components used in this project Arduino Uno ESP-01 ESP8266 WiFi module USB to TTL converter Solderless Breadboard - Half+ Breadboard power supply module - 3.3V/ 5V RGB LEDs (x3) - Common Anode Resistors (x3) - 220 Ω Relay module - 5V single channel Male-to-Male Jumper wires Female-to-Male Jumper wires Setup Your setup must look somewhat similar to that shown in the images above. Connections ESP8266 ESP-01 wifi module GND - Ground GPIO0- Not connected GPIO2 - Not connected RXD - D2 TXD - D3 CH_PD - VCC - 3.3V RESET - Not connected VCC - 3.3V  *Note: Do not connect your ESP8266 ESP-01 wifi module with 5V. RGB LED - Common Anode Anode -...
2 comments
Read more

73. Limit the crowd to prevent the spread of COVID-19

Hey everyone! Today I am going to explain you about another interesting COVID-19 Arduino project. This is an automatic, effective and cheap method to limit the crowd in public places - such as shopping malls, supermarkets, offices, etc. - and public transport vehicles, such as buses and trains. The World Health Organization, WHO, has advised people to stay away from crowded places to protect themselves from the spread of Coronavirus disease. Even though people practice social distancing, it may not be effective when they are present in crowded places. I came up with this idea after I read the WHO guidelines about preventing the spread of COVID-19. Aim/ Objective This project is an automatic, cheap and effective way of limiting the crowd in public places and vehicles. Using a human to limit the number of people in a particular place would not be as effective as using an automatic system, due to lack of staff members in some areas. This prototype can be used in real-life situations by ...
8 comments
Read more