Skip to main content

19. Prototype - Human Detection box

Hello everyone!

In this project, we will be learning how to make a Human detection box. For this project we will be using a Passive Infrared (PIR) Sensor to detect movements, animals or humans (anything else that emits IR radiation). One drawback of this project may include that the alarm in the box can be falsely triggered by wind or sudden change in surrounding temperature.
This box is useful in areas where humans or animals are restricted.



*Precaution: 
Mains electricity is extremely dangerous. Safety must not be compromised. Here are few safety precautions that you must follow when you handle mains electricity:
https://www.atlantictraining.com/blog/15-safety-precautions-electricity/

Supplies

  • Arduino Uno
  • Solderless Breadboard - Mini
  • Power Bank - 10000 mAh
  • Male-to-Male Jumper wires - 10 cm (x2)
  • Female-to-Male Jumper wires - 20 cm (x9)
  • PIR sensor
  • Buzzer module (KY-012)
  • Relay module
  • LED - any colour
  • Resistor - 1 kΩ
  • USB 2.0 Type A cable (Power bank)
  • USB 2.0 Type A/B cable (Arduino Uno)

Setup



For a detailed explanation of the setup, please watch the YouTube video posted at the bottom of this page.

Connections


  • Relay module - D3
  • Buzzer module - D5
  • PIR sensor - D6

(+) pins of all three components were connected to 5V, while (-) pins were connected to GND (Ground).

Coding

*The codes are incomplete. You can either request the codes at arduinoprojectsbyr@gmail.com or write them according to your interest.

Final Look

If anyone has any questions or suggestions about this projects, please comment them below or feel free to send them at arduinoprojectsbyr@gmail.com

Comments

Post a Comment

Popular posts from this blog

77. Controlling Micro servo Robotic Arm with MPU-6050 sensor module

 Hey everyone! I am back with an interesting project. Today, you will be learning about controlling a Simple 2 axis Robotic Arm, made from Micro servo motors, with an MPU-6050 sensor module. Please feel free to visit my previous blog post to learn about the MPU-6050 sensor module. Hardware components used in this project Arduino Mega 2560 - You could use any other Arduino microcontroller, but make sure you use an external power supply. USB Type A/B cable (for Arduino Mega 2560) MPU-6050 sensor module SG-90 Tower Pro Micro Servo motor (x2) Male-to-Male Jumper wires (x6) Male-to-Female Jumper wires (x5) Setup Schematic MPU-6050 sensor module VCC - 3.3V GND - Ground SDA - D20 (Arduino Mega 2560), A4 (Arduino Uno and Nano) SCL - D21 (Arduino Mega 2560), A5 (Arduino Uno and Nano) INT - D2 Micro servo motor (Roll) S (Yellow/ Orange) - D9 + (Red) - 5V - (Black/ Brown) - GND  Micro servo motor (Pitch) S (Yellow/ Orange) - D10 + (Red) - 5V - (Black/ Brown) - GND Coding As I alread...
Post a Comment
Read more

57. Using Blynk with Arduino Uno and ESP8266 WiFi module

Hello Everyone! Today I am going to explain you how to connect your Arduino Uno with Blynk using the ESP8266 WiFi module. I have already demonstrated you about connecting your Arduino Uno with Blynk app using the Ethernet Shield W5100 and this will be the second version of that project .  Hardware components used in this project Arduino Uno ESP-01 ESP8266 WiFi module USB to TTL converter Solderless Breadboard - Half+ Breadboard power supply module - 3.3V/ 5V RGB LEDs (x3) - Common Anode Resistors (x3) - 220 Ω Relay module - 5V single channel Male-to-Male Jumper wires Female-to-Male Jumper wires Setup Your setup must look somewhat similar to that shown in the images above. Connections ESP8266 ESP-01 wifi module GND - Ground GPIO0- Not connected GPIO2 - Not connected RXD - D2 TXD - D3 CH_PD - VCC - 3.3V RESET - Not connected VCC - 3.3V  *Note: Do not connect your ESP8266 ESP-01 wifi module with 5V. RGB LED - Common Anode Anode -...
2 comments
Read more

73. Limit the crowd to prevent the spread of COVID-19

Hey everyone! Today I am going to explain you about another interesting COVID-19 Arduino project. This is an automatic, effective and cheap method to limit the crowd in public places - such as shopping malls, supermarkets, offices, etc. - and public transport vehicles, such as buses and trains. The World Health Organization, WHO, has advised people to stay away from crowded places to protect themselves from the spread of Coronavirus disease. Even though people practice social distancing, it may not be effective when they are present in crowded places. I came up with this idea after I read the WHO guidelines about preventing the spread of COVID-19. Aim/ Objective This project is an automatic, cheap and effective way of limiting the crowd in public places and vehicles. Using a human to limit the number of people in a particular place would not be as effective as using an automatic system, due to lack of staff members in some areas. This prototype can be used in real-life situations by ...
8 comments
Read more